|
規 格 書
SPECIFICATION
|
|
DESIGNATION
|
系列：DC JACK
|
|
MODEL
|
型號：DC-022
|
|
1. RATING
|
額定值: DC30V 0.5A
|
|
2. CONSTRUCTION DIMENSION結構尺寸：
|
Apply to the appended drawing：符合附加圖紙
|
|
3.APPEARANCE外觀：
|
Have no remarkable damage ,crack and rust etc：無明顯損傷,裂紋,鏽跡等.
|
|
ITEM 專案
|
TEST CONDITION 測試條件
|
SPECIFICATION規格
|
|
4. ELECTRONICAL CHARACTERISTICS.電氣性能.
|
|
4A
|
CONTACT RESISTANCE接觸阻抗
|
Being measured at 1KHz small current contact resistance meter.在1KHZ小電流下測量.
|
30mΩ max
30毫歐以下.
|
|
4B
|
INSULATION
RESISTANCE
絕緣阻抗
|
Measurements shall be made following application of DC500V potential across terminals and across terminals and frame for 1 minute. 在端子之間和端子與殼之間加DC 500V條件下,持續1分鐘測量.
|
100MΩ min
100兆歐以上.
|
|
4C
|
WITHSTAND
VOLTAGE
耐電壓
|
AC 500V (50Hz or 60Hz) shall be applied across terminals and across terminals and frame for one minute在端子之間和端子與殼之間加ＡC 500V(50HZ或60HZ)條件下,持續1分鐘測量.
|
There shall be no breakdown.
無擊穿現象出現.
|
|
5. MECHANICAL CHARACTERISTICS.機械性能.
|
|
5A
|
INSERTION AND WITHDRAW
FORCE 插拔力
|
Being measure at across spring piece and across matching plug for ergometer
用測力計在插頭與彈片之間進行測量．
|
Insertion and extraction force 5-18N
插拔力 5-18N
|
|
5B
|
TERMINAL STRENGTH
端子強度
|
A static force of 500gf being applied in one direction on the tip of terminal for 1 minute.一個500克之靜負荷施加於端子頂部的一個方向持續1分鐘。
|
There shall be no sign of damage mechanically and electrically.無任何跡象顯示機械及電氣性能之損壞.
|
|
6. DURABILITY.耐久性.
|
|
6A
|
SOLDERING TEST.
可焊性試驗
|
The tip of the terminals shall be dipped 2mm in the solder bath at a temperature of 230±5℃ for 3±0.5sec.端子頂部被浸入焊錫池2mm深,溫度230±5℃時間3±0.5秒。
|
A new uniform coating of solder shall cover a minimum of 90 of the surface being immersed.浸入的部分90%以上表面將被錫覆蓋.
|
|
6B
|
LIFE TEST.
壽命試驗
|
5,000 cycles of operation at a rate of 20-30 cycles per minute with unloading.
無負載條件下,每分鐘20-30次的速度操作5,000次。
|
(1). Contact resistance . 40mΩmax接觸阻抗 40毫歐以下.
(2). Insertion and withdraw force 30 initial value插拔力變化範圍初始值30%
(3). ITEM 專案-4B
(4). ITEM 專案-4C
(5). ITEM 專案-5B
|
|
6C
|
HEAT TEST.
耐熱試驗
|
85±2℃ for 48 hours after test keep in normal condition for 30 minutes.在85±2℃環境中放48小時,再放在正常環境中30分鐘後進行測試。
|
(1). Contact resistance 50mΩ max.接觸電阻50毫歐以下
(2). Insulation resistance. 50MΩ min. 絕緣電阻50兆歐以上
(3). There shall be no sign of damage mechanically and electrically. 無任何跡象顯示機械及電器性能之損壞.
|
|
6D
|
HUMIDITY TEST.
耐濕試驗
|
89% RH for 48 hrs. after test keep in normal condition for 30 min.在89% RH環境中放48小時,再放在正常環境中30分鐘後進行測試。
|
|
6E
|
COLD TEST.
耐冷試驗
|
At –40±2℃ for 48 hrs. after test keep in normal condition for 30 min.在-40±2℃環境中放48小時,再置於正常環境中30分鐘後進行測試。
|
|
DGN.製錶人：
|
CKD.校 對：
|
APPD.審核：
|
|
DATE.日期：
|
DATE.日期：
|
DATE.日期：
|
當前位置:
